EICON TECHNOLOGY CORPORATION

DIVA MOBILE V.90 PC CARD (S/T INTERFACE)
Card Type ISDN modem (asynchronous)
ISDN Transfer Rate 128 Kbps
Topology Star
Wiring Type Unshielded twisted pair
ISDN Protocol HDLC, X.75, T.90NL, T.70NL, V.120, ETSI/DSS1, NI-1, AT&T 5ESS, 1TR6, INS-Net 64, TPH 1962, VN3, CT1, Sweden National, DSSI
Maximum Modem Rate 56Kbps
Maximum Fax Rate 14.4Kbps
Data Modulation Protocol Bell 103J/212A
ITU-T V.8bis, V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34, V.90, Rockwell V.FC
Fax Modulation Protocol ITU V.17, V.21, V.27ter, V.29
Error Correction/Compression ITU V.42, V.42bis, MNP5, LAP-M
Fax Class Class I & 2
Data Bus PCMCIA Type II/PCMCIA Type III


CONNECTIONS

Function

Location

Function

Location
RJ-45 UTP connector CN1 S/T interface PC Card connector CN2
Note: A separate NT1 terminating resistor is required for S/T interface.


SUPPORTED COMMAND SET

Basic AT Commands

AT, ‘+++’, ‘comma’, A/
A, H, O, P, T, U, Z
&J, &W

Extended AT Commands

%Q

S Registers

S18
Note: See MHI Help File for full command documentation.



Proprietary Command Set



COMMUNICATION PROTOCOLS
Type: Configuration
Format: AT [cmds] Bn [cmds]
Description: Selects the communication protocol for low speed connections.

Command

Protocol

 

B0

 CCITT

»

B1

 Bell 212A


DIAL
Type: Immediate
Format: AT [cmds] D<#> [cmds]
Description: Dials telephone number and goes to data mode after connection is made.


ECHO
Type: Configuration
Format: AT [cmds] En [cmds]
Description: Enables modem to echo commands back to terminal.

Command

Function

 

E0

 Echo function disabled

»

E1

 Echo function enabled


REPORT INFORMATION
Type: Immediate
Format: AT [cmds] In [cmds]
Description: Displays information requested.

Command

Function

I0

 Reports product information

I1

 Reports ROM checksum

I2

 Tests and reports ROM checksum

I3

 Reports firmware revision
I4 Reports identifier string
I5 Reports country code
I6 Reports data pump model and internal code revision


SPEAKER MODE
Type: Configuration
Format: AT [cmds] Mn [cmds]
Description: Selects various speaker options.

Command

Function

 

M0

 Speaker disabled

»

M1

 Speaker enabled until carrier signal detected

 

M2

 Speaker enabled

 

M3

 Speaker enabled following dialing, then disabled after carrier signal detected


AUTO-MODE DETECTION
Type: Configuration
Format: AT [cmds] Nn [cmds]
Description: Selection of auto-mode detection

Command

Function

 

N0

 Auto-mode detection disabled

»

N1

 Auto-mode detection enabled


RESULT CODES
Type: Configuration
Format: AT [cmds] Qn [cmds]
Description: Enables modem to send result codes to the DTE.

Command

Function

»

Q0

 Result code sending enabled

 

Q1

 Result code sending disabled


STATUS-REGISTER
Type: Configuration
Format: AT [cmds] Sn=x [cmds]
Description: Sets S-register n to decimal value x.
Note: Range of n value is 0-27. Range of x value is 0-255.


RESULT CODE FORMAT
Type: Configuration
Format: AT [cmds] Vn [cmds]
Description: Selects word or numeric format for information-text and result codes.

Command

Function

 

V0

 Numeric format enabled

»

V1

 Verbose (word) format enabled


EXTENDED RESULT CODES
Type: Configuration
Format: AT [cmds] Wn [cmds]
Description: Enables selection of additional result codes.

Command

Function

»

W0

 Enables CONNECT result codes to report DTE speed

 

W1

 Enables CONNECT result codes to report line speed, error control protocol and DTE speed

 

W2

 Enables CONNECT result codes to report DCE speed


SELECT CALL PROGRESS RESULT CODES
Type: Configuration
Format: AT [cmds] Xn [cmds]
Description: Result code format options.

Command

Function

 

X0

 Result codes 0 - 4 enabled

 

X1

 Busy and dial tone detection result codes disabled

 

X2

 Busy tone detection result codes disabled

 

X3

 Dial tone detection result codes disabled

»

X4

 All result codes enabled


LONG SPACE DISCONNECT
Type: Configuration
Format: AT [cmds] Yn [cmds]
Description: Commands the modem to disconnect after long space is detected.

Command

Function

»

Y0

 Long space disconnect function disabled

 

Y1

 Long space disconnect function enabled


DATA CARRIER DETECT (DCD)
Type: Configuration
Format: AT [cmds] &Cn [cmds]
Description: Selects whether the carrier detect option is enabled or disabled.

Command

Function

 

&C0

 Carrier detect enabled

»

&C1

 Carrier detect enabled after carrier signal detected


DATA TERMINAL READY (DTR)
Type: Configuration
Format: AT [cmds] &Dn [cmds]
Description: Selects modem response to DTR.

Command

Function

 

 &D0 Modem does not respond to DTR

 

 &D1 Modem goes to command mode after DTR goes off

»

 &D2 Modem goes to command mode and disconnects (hangs up) after DTR goes off

 

 &D3 Modem is initialized after DTR goes off; loads stored configuration profile set by &Yn


FACTORY DEFAULT PROFILE
Type: Configuration
Format: AT [cmds] &F [cmds]
Description: Sets values in active profile to values found in the default profile.
Command Function
&F0 Factory configuration 0
&F1 Factory configuration 1


GUARD TONE
Type: Configuration
Format: AT [cmds] &Gn [cmds]
Description: Commands the modem to transmit a guard tone.
Note: Used primarily for international data transmission.

Command

Function

»

&G0

 Guard tone disabled

 

&G1

 Guard tone disabled

 

&G2

 1800Hz guard tone enabled


FLOW CONTROL
Type: Configuration
Format: AT [cmds] &Kn [cmds]
Description: Enables flow control options.

Command

Function

 

&K0

 Flow control disabled

»

&K3

 RTS/CTS flow control enabled

 

&K4

 XON/XOFF flow control enabled

 

&K5

 Transparent XON/XOFF flow control enabled

 

&K6

 RTS/CTS and XON/XOFF flow control enabled


COMMUNICATIONS MODE
Type: Configuration
Format: AT [cmds] &Qn [cmds]
Description: Selects communications mode options.

Command

Mode

 

&Q0

 Asynchronous mode

 

&Q4

 Auto-synchronous mode

»

&Q5

 Error correction mode

 

&Q6

 Buffered asynchronous mode


TEST MODES
Type: Immediate
Format: AT [cmds] &Tn
Description: Selects test options.

Command

Function

 

&T0

 End current test

 

&T1

 Begin local analog loopback test

 

&T3

 Begin local digital loopback

 

&T4

 Grant remote digital loopback request

»

&T5

 Deny remote digital loopback request

 

&T6

 Begin remote digital loopback

 

&T7

 Begin remote digital loopback and self-test

 

&T8

 Begin local analog loopback and self-test


CONFIGURATION PROFILES
Type: Immediate
Format: AT [cmds] &V [cmds]
Description: Displays active and stored configuration profiles as well as the first four stored telephone numbers.


DEFAULT PROFILE SELECTION
Type: Configuration
Format: AT [cmds] &Yn [cmds]
Description: Selects which user profile will be the default.

Command

Function

»

&Y0

 Profile 0 is the default user profile

 

&Y1

 Profile 1 is the default user profile


STORE TELEPHONE NUMBER
Type: Configuration
Format: AT [cmds] &Zn=(phone # & modifiers)
Description: Writes selected telephone numbers into the non-volatile memory at location n.
Note: Telephone numbers and modifiers can include up to 34 characters. Default is &Z1.



Extended AT Commands



MAXIMUM BLOCK SIZE FOR TRANSMISSION
Type: Configuration
Format: AT [cmds] \An [cmds]
Description: Sets the maximum transmittable block size.

Command

Function

 

\A0

 MNP block size is 64 characters

»

\A1

 MNP block size is 128 characters

 

\A2

 MNP block size is 192 characters

 

\A3

 MNP block size is 256 characters


BREAK SEND
Type: Configuration
Format: AT [cmds] \Bn [cmds]
Range: Unidentified
Unit: .01 second
Description: Sends break to modem.


BREAK TYPE
Type: Configuration
Format: AT [cmds] \Kn [cmds]
Description: Configures action of break signal.

Command

Break from remote

Break from DTE (reliable mode)

Break received from DTE (normal mode)

 

\K0

 Break sent and buffers cleared Command mode enabled Break sent and command mode enabled

 

\K1

 Break sent and buffers cleared Break sent and buffers cleared Break sent

 

\K2

 Break sent and buffers saved Command mode enabled Break sent and command mode enabled

 

\K3

 Break sent and buffers saved Break sent and buffers saved Break sent

 

\K4

 Send break with transmitted data Command mode enabled Break sent and command mode enabled

»

\K5

 Send break with transmitted data Send break with transmitted data Break sent


ERROR CORRECTION MODE
Type: Configuration
Format: AT [cmds] \Nn [cmds]
Description: Controls the error-correction mode.

Command

Function

 

\N0

 Normal mode enabled (speed buffering)

 

\N1

 Direct mode enabled (no speed buffering)

 

\N2

 V.42 reliable mode enabled (fallbacks to MNP - V.42 or MNP only)

»

\N3

 Auto-reliable mode enabled (V.42, MNP or normal)

 

\N4

 V.42 reliable mode enabled (V.42 only)

 

\N5

 MNP reliable mode enabled (MNP only)


CONNECT MESSAGE FORMAT CONTROL
Type: Configuration
Format: AT [cmds] \Vn [cmds]
Description: Selects extended result codes.
Default: \V0  
Note: Single-line messages only. CONNECT <DTE SPEED></Modulation></Protocol></Compression></Line Speed>

Command

Function

»

\V0

 Connect messages controlled by command settings X, W and S95

 

\V1

 Connect messages subject to B and Q commands


COMPRESSION
Type: Configuration
Format: AT [cmds] %Cn [cmds]
Description: Selects data compression.

Command

Function

 

%C0

 Data compression disabled

 

%C1

 MNP5 enabled

 

%C2

 V.42bis enabled

»

%C3

 MNP5 and V.42bis; or data compression and correction enabled


AUTO-RETRAIN & LINE QUALITY MONITOR
Type: Configuration
Format: AT [cmds] %En [cmds]
Description: Controls auto-retrain mode and fallback/fall-forward.

Command

Function

 

%E0

 Auto-retrain and line-quality monitor disabled

 

%E1

 Auto-retrain and line-quality monitor enabled

»

%E2

 Auto-fallback/fall-forward and line-quality monitor enabled


LINE SIGNAL LEVEL
Type: Immediate
Format: AT [cmds] %L [cmds]
Range: Unidentified
Unit: Unidentified
Description: Returns a value which indicates the received line signal level.


MNP10 - LINK NEGOTIATION
Type: Configuration
Format: AT [cmds] *Hn [cmds]
Description: Sets the speed at which MNP10 link negotiation will occur.

Command

Function

»

*H0

 Link will be negotiated at highest possible speed

 

*H1

 Link will be negotiated at 1200bps

 

*H2

 Link will be negotiated at 4800bps


MNP - EXTENDED SERVICES
Type: Configuration
Format: AT [cmds] -Kn [cmds]
Description: Selects MNP extended services.

Command

Function

»

-K0

 MNP extended services disabled

 

-K1

 MNP extended services enabled

 

-K2

 MNP extended services enabled without indicating MNP on the answer detection phase


MNP10 - FALLBACK
Type: Configuration
Format: AT [cmds] -Qn [cmds]
Description: Allows MNP to fall back from high speed V.34, V.32 bis, or V.32 to lower speed V.22 bis or V.22.

Command

Function

 

-Q0

 MNP at 2400 and 1200bps disabled

»

-Q1

 MNP at 2400 and 1200bps enabled


MNP10-EC
Type: Configuration
Format: AT [cmds] -SEC=n [cmds]
Default: -SEC=0
Description: Controls MNP10-EC


INITIAL TRANSMISSION LEVEL
Type: Configuration
Format: AT [cmds] @Mn [cmds]
Default: @M0
Range: Unidentified
Unit: Unidentified
Description: Sets the level for initial transmission.


V.32 - COMPROMISE EQUALIZER
Type: Configuration
Format: AT [cmds] :En [cmds]
Default: :E1
Description: Controls V.32 compromise equalizer.


CALLER ID
Type: Configuration
Format: AT [cmds] #CID=n [cmds]
Description: Controls the Caller ID function.

Command

Function

»

#CID=0

 Caller ID disabled

 

#CID=1

 Caller ID displays formatted data

 

#CID=2

 Caller ID displays raw hexadecimal data


MODULATION SELECTION
Type: Immediate
Format: AT [cmds] +MS? [cmds]
Description: Selects modulation, automode, minimum rate and maximum rate settings, m-Law or A-Law and robbed bit signaling generation or detection.
Note: Command format is: +MS= <mod> [,[<automode>][,[<min_rate>][,[<max_rate>][,[<x_law>][,[<rb_signaling>]]]]]]<CR>



S(status) -REGISTERS



AUTO ANSWER RING COUNT
Type: Register
Format AT [cmds] S0=n [cmds]
Default: 0
Range: Unidentified
Unit: 1 ring
Description: Sets the number of rings allowed before the modem automatically goes off-hook.
Note: If S0=0, automatic-answering is disabled.


RING COUNT
Type: Register
Format AT [cmds] S1? [cmds]
Default: 0
Range: Unidentified
Unit: 1 ring
Description: Counts the number of ring-cycles the modem receives.


ESCAPE CHARACTER
Type: Register
Format AT [cmds] S2=n [cmds]
Default: 43
Range: 0-255
Unit: ASCII
Description: Selects a character used for the escape sequence.


CARRIAGE RETURN CHARACTER
Type: Register
Format AT [cmds] S3=n [cmds]
Default: 13
Range: 0-127
Unit: ASCII
Description: Selects a character used for carriage return <CR>.


LINE FEED CHARACTER
Type: Register
Format AT [cmds] S4=n [cmds]
Default: 10
Range: 0-127
Unit: ASCII
Description: Selects a character used for line feed <LF>.


BACKSPACE CHARACTER
Type: Register
Format AT [cmds] S5=n [cmds]
Default: 8
Range: 0-32
Unit: ASCII
Description: Selects a character used for backspace <BS>.


DIALING TONE DELAY
Type: Register
Format AT [cmds] S6=n [cmds]
Default: 2
Range: 2-255
Unit: 1 second
Description: Duration of delay after modem goes off-hook and before dialing.


NO CARRIER TIME-OUT
Type: Register
Format AT [cmds] S7=n [cmds]
Default: 50
Range: 1-255
Unit: 1 second
Description: Maximum wait time the modem uses after dialing to detect a carrier signal from the remote modem for both originating and answering calls.


PAUSE DURATION
Type: Register
Format AT [cmds] S8=n [cmds]
Default: 2
Range: 0-255
Unit: 1 second
Description: Duration of pause per comma (,) command used in a command or dial string.


CARRIER DETECT RESPONSE TIME
Type: Register
Format AT [cmds] S9=n [cmds]
Default: 6
Range: 1-255
Unit: .1 second
Description: The amount of time the remote modem’s carrier signal is present before local modem will issue a carrier detect.


CARRIER LOSS RESPONSE TIME
Type: Register
Format AT [cmds] S10=n [cmds]
Default: 14
Range: 1-255
Unit: .1 second
Description: Maximum time allowed by the modem after losing the carrier signal and prior to initiating hang-up process.


TONE PULSE DURATION
Type: Register
Format AT [cmds] S11=n [cmds]
Default: 95
Range: 50-255
Unit: 1 ms
Description: DTMF tone pulse duration and time between tone pulses for tone dialing operations.


ESCAPE SEQUENCE GUARD TIME
Type: Register
Format AT [cmds] S12=n [cmds]
Default: 50
Range: 0-255
Unit: 20 ms
Description: Maximum allowable time between escape character sequence initiation and completion for the escape sequence to be executed.


BIT-MAPPED REGISTER S14
Format: AT [cmds] S14=n [cmds]
Default: 138 (8Ah)
Range: Unidentified
Unit: Bit-mapped
Description: Status of general bit-mapped options.


TEST MODES
Type: Register
Format: AT [cmds] S16=n [cmds]
Default: 0
Range: Unidentified
Unit: Unidentified
Description: Status of test mode bit-mapped options. (&T)


AUTOSYNC OPTIONS
Format: AT [cmds] S19=n [cmds]
Default: 0
Description: AutoSync options.


AUTOSYNC HDLC ADDRESS & BSC SYNC CHARACTER
Type: Register
Format: AT [cmds] S20=n [cmds]
Default: 0
Range: 0-255
Unit: 1 second
Description: AutoSync HDLC address & BSC Sync character selection.


BIT-MAPPED REGISTER S21
Format AT [cmds] S21=n [cmds]
Default: 52 (34h)
Range: Unidentified
Unit: Bit-mapped
Description: Status of V.24/general bit-mapped options.


BIT-MAPPED REGISTER S22
Format AT [cmds] S22=n [cmds]
Default: 117 (75h)
Range: Unidentified
Unit: Bit-mapped
Description: Controls speaker volume and controls, limits results codes.


BIT-MAPPED REGISTER S23
Format AT [cmds] S23=n [cmds]
Default: 62 (36h)
Range: Unidentified
Unit: Bit-mapped
Description: Status of general bit-mapped options.


SLEEP TIMER
Type: Register
Format AT [cmds] S24=n [cmds]
Default: 10
Range: 0-255
Unit: 1 second
Description: Maximum duration of DTE and DCE inactivity allowed prior to initiating low-power sleep mode.


DELAY TO DTR OFF
Type: Register
Format AT [cmds] S25=n [cmds]
Default: 5
Range: 0-255
Unit: 1 second
Description: Sets the time the modem will wait until DTR disconnects.


RTS TO CTS DELAY
Type: Register
Format AT [cmds] S26=n [cmds]
Default: 1
Range: 0 - 255
Unit: .01 second
Description: Sets the duration of delay for CTS to respond to RTS status change.


BIT-MAPPED REGISTER S27
Format AT [cmds] S27=n [cmds]
Default: 73 (49h)
Range: Unidentified
Unit: Bit-mapped
Description: Status of general bit mapped options.


BIT-MAPPED REGISTER S28
Format AT [cmds] S28=n [cmds]
Default: 0
Range: Unidentified
Unit: Bit-mapped
Description: Status of general bit-mapped options.


INACTIVITY TIMER
Type: Register
Format AT [cmds] S30=n [cmds]
Default: 0
Range: 0-255
Unit: 0.1 seconds
Description: Maximum duration of DTE and DCE inactivity allowed prior to initiating hang-up process.
Note: S30=0 disables the timer and allows indefinite inactivity.


BIT-MAPPED REGISTER S31
Format: AT [cmds] S31=n [cmds]
Default: 194
Range: Unidentified
Description: Status of general bit-mapped options.


FLOW CONTROL CHARACTER - XON
Type: Register
Format: AT [cmds] S32=n [cmds]
Default: 17 (11h)
Range: 0-255
Unit: ASCII
Description: Sets the character used to represent XON.


FLOW CONTROL CHARACTER - XOFF
Type: Register
Format: AT [cmds] S33=n [cmds]
Default: 19 (13h)
Range: 0-255
Unit: ASCII
Description: Sets the character used to represent XOFF.


LAPM FAILURE CONTROL
Type: Register
Format AT [cmds] S36=n [cmds]
Default: 7
Description: Selects the action of the modem if it fails to connect.


LINE CONNECTION SPEED
Type: Register
Format AT [cmds] S37=n [cmds]
Default: 0
Description: Sets the maximum allowable data exchange rate attempted during handshake process.


FORCED DISCONNECT DELAY
Type: Register
Format AT [cmds] S38=n [cmds]
Default: 20
Range: 0-255
Unit: 1 second
Description: Sets maximum duration allowed after losing carrier-signal or receiving a clear call signal from the remote modem and before initiating hang-up process.


FLOW CONTROL
Type: Register
Format AT [cmds] S39=n [cmds]
Default: 3
Description: Status of flow control options.


BIT-MAPPED REGISTER S40
Format AT [cmds] S40=n [cmds]
Range: Unidentified
Unit: Bit-mapped
Description: Status of general bit-mapped options.


BIT-MAPPED REGISTER S41
Format AT [cmds] S41=n [cmds]
Default: 195
Range: Unidentified
Unit: Bit-mapped
Description: Status of general bit-mapped options.


DATA COMPRESSION
Type: Register
Format: AT [cmds] S46=n [cmds]
Default: 138
Range: 136, 138
Description: Selects compression.


V.42 NEGOTIATION CONTROL
Type: Register
Format: AT [cmds] S48=n [cmds]
Default: 7
Description: Negotiation selection.


LAPM BREAK CONTROL
Type: Register
Format AT [cmds] S82=n [cmds]
Default: 128 (40h)
Description: Sets the method for break transmission during error-control.


CONNECTION FAILURE CODES
Type: Register
Format AT [cmds] S86? [cmds]
Range: 0, 4, 5, 9, 12, 13, 14
Description: Reports codes which correspond to the possible causes of a connection failure.


TRANSMISSION LEVEL - PSTN
Type Register or Configuration
Format AT [cmds] S91=n [cmds]
Default: 10
Range 0-15
Unit -1 dBm
Description Sets the signal level for transmission over switched phone lines.


TRANSMISSION LEVEL - FAX
Type: Register
Format: AT [cmds] S92=n [cmds]
Default: 10
Range: 0-15
Unit: -1 dBm
Description: Sets the signal level for transmission while in fax mode.


RESULT CODES
Type: Register
Format AT [cmds] S95=n [cmds]
Default: 0
Range: Unidentified
Unit: Unidentified
Description: Works in combination with the Wn command to enable result codes.