WS-5614CM3
| Card Type | Modem |
| Chip Set | Unidentified |
| Maximum Modem Rate | 56Kbps |
| Maximum Fax Rate | 14.4Kbps |
| Data Modulation Protocol | Bell 103/212 ITU-T V.22, V.22bis, V.32, V.32bis, V.34, 56Kflex, V.90 |
| Fax Modulation Protocol | ITU-T V.17, V.21 CH.2, V.27ter, V.29 |
| Error Correction/Compression | MNP5, V.42, V.42bis |
| Fax Class | Class I |
| Data Bus | PCMCIA |
55486
SUPPORTED COMMAND SET |
Basic AT Commands |
| AT, ‘+++’, A/ |
| A, B, E, H, M, O, P, Q, T, V, W, X, Y, Z |
| &C, &P, &T, &V, &W, &Y, &Z |
Extended AT Commands |
| %C, %E, %L, %Q |
| \A, \B, \K, \N |
Special Commands |
S Registers |
| S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25 |
| S26, S27, S29, S30, S31, S32, S33, S36, S37, S38, S39, S40, S41, S91, S92, S95 |
| Note: See MHI Help File for full command documentation. |
PROPRIETARY AT COMMAND SET
AUTO-MODE DETECTION |
||
| Type: | Configuration | |
| Format: | AT [cmds] Nn [cmds] | |
| Description: | Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed. | |
Command |
Function |
|
| N0 | In originate mode, handshake begins at line speed designated by the S37 register and the B command | |
| N1 | In originate mode, handshake begins at line speed designated by the S37 register. and the B command Modem can shift to a slower speed if necessary. | |
COMMUNICATIONS MODE |
|
| Type: | Configuration |
| Format: | AT [cmds] &Mn [cmds] |
| Description: | Selects communications mode |
Command |
Mode |
&M0 |
Asynchronous mode |
COMMUNICATIONS MODE |
||
| Type: | Configuration | |
| Format: | AT [cmds] &Qn [cmds] | |
| Description: | Selects communications mode options | |
Command |
Mode |
|
&Q0 |
Asynchronous mode, serial port speed follows connect speed. | |
| » | &Q5 |
Error correction mode |
&Q6 |
Buffered asynchronous mode | |
DATA SET READY (DSR) |
|
| Type: | Configuration |
| Format: | AT [cmds] &Sn [cmds] |
| Description: | Selects DSR options |
Command |
Function |
&S0 |
DSR forced high |
&S1 |
DSR high only while modem is handshaking or connected |
DATA TERMINAL READY (DTR) |
||
| Type: | Configuration | |
| Format: | AT [cmds] &Dn [cmds] | |
| Description: | Selects modem response to DTR | |
Command |
Mode |
|
&D0 |
DTR ignored | |
&D1 |
DTR toggle causes online command mode | |
| » | &D2 |
DTR toggle causes modem to go on-hook |
&D3 |
Modem reset on DTR toggle | |
DIAL |
|
| Type: | Immediate |
| Format: | AT [cmds] D<#> [cmds] |
| Description: | Dials telephone number according to any modifiers included in the string |
| Note: | Any combination of modifiers can be used to produce the desired dial functions in sequence. |
Command |
Function |
DL |
Re-dial last number |
DP |
Pulse dialing enabled |
DS=n |
Dial stored telephone number n (0-3) |
DT |
Tone dialing enabled/Pulse dialing disabled |
DW |
Dialing resumed following dial tone detection |
D, |
Dialing paused for amount of time specified in S8 register |
D"WXY" |
Optional method of denoting telephone numbers. Letters enclosed in quotes are interpreted as numbers according to the system found on a telephone keypad. |
D! |
Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. |
D@ |
Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by 5 seconds of silence, is received prior to executing the rest of the dial string. |
D& |
Wait for credit card "bong" tone before processing the remaining characters in the dial string |
D; |
Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. |
FACTORY DEFAULT PROFILE |
|
| Type: | Configuration |
| Format: | AT [cmds] &F [cmds] |
| Description: | Sets values in active profile to values found in the default profile |
&F0 |
Load factory configuration 0 |
&F1 |
Load factory configuration 1 |
FLOW CONTROL |
|
| Type: | Configuration |
| Format: | AT [cmds] &Kn [cmds] |
| Description: | Enables flow control options |
Command |
Function |
&K0 |
Flow control disabled |
&K3 |
RTS/CTS flow control enabled |
&K4 |
XON/XOFF flow control enabled |
&K5 |
Transparent XON/XOFF flow control enabled |
&K6 |
Both RTS/CTS & XON/XOFF flow control enabled |
GUARD TONE |
||
| Type: | Configuration | |
| Format: | AT [cmds] &Gn [cmds] | |
| Description: | Commands the modem to transmit a guard tone in V.22/V.22bis | |
| Note: | Used primarily for international data transmission | |
Command |
Function |
|
| » | &G0 |
Guard tone disabled |
&G1 |
Guard tone disabled | |
&G2 |
1800Hz guard tone enabled | |
REPORT INFORMATION |
|
| Type: | Immediate |
| Format: | AT [cmds] In [cmds] |
| Description: | Displays information requested |
Command |
Function |
I0 |
Reports product code |
I1 |
Reports ROM checksum |
I2 |
Tests and reports ROM checksum |
I3 |
Reports firmware & product ID string |
SPEAKER VOLUME |
||
| Type: | Configuration | |
| Format: | AT [cmds] Ln [cmds] | |
| Description: | Controls speaker volume | |
Command |
Function |
|
L0 |
Low volume setting | |
| » | L1 |
Low volume setting |
L2 |
Medium volume setting | |
L3 |
Highest volume setting | |
EXTENDED AT COMMAND SET
MODULATION SELECTION |
|
| Type: | Configuration |
| Format: | AT [cmds] +MS=x,y,z,a,b,c [cmds] |
| Description: | Sets options for active protocol; the transfer rates specified by z and a must be valid for the protocol selected. |
Command |
Function |
x=0 |
V.21 |
x=1 |
V.22 |
x=2 |
V.22bis |
x=3 |
V.23 |
x=9 |
V.32 |
x=10 |
V.32bis |
x=11 |
V.34, K56flex |
x=64 |
Bell 103 |
x=69 |
Bell 212A |
x=74 |
V.FC |
y=0 |
Automode disabled |
y=1 |
Auto-detect highest speed enabled |
z, a=300 |
Set minimum or maximum transfer rate at 300bps, respectively. |
z, a=1200 |
Set minimum or maximum transfer rate at 1200bps, respectively. |
z, a=2400 |
Set minimum or maximum transfer rate at 2400bps, respectively. |
z, a=4800 |
Set minimum or maximum transfer rate at 4800bps, respectively. |
z, a=7200 |
Set minimum or maximum transfer rate at 7200bps, respectively. |
z, a=9600 |
Set minimum or maximum transfer rate at 9600bps, respectively. |
z, a=12000 |
Set minimum or maximum transfer rate at 12000bps, respectively. |
z, a=14400 |
Set minimum or maximum transfer rate at 14400bps, respectively. |
z, a=16800 |
Set minimum or maximum transfer rate at 16800bps, respectively. |
z, a=19200 |
Set minimum or maximum transfer rate at 19200bps, respectively. |
z, a=21600 |
Set minimum or maximum transfer rate at 21600bps, respectively. |
z, a=24000 |
Set minimum or maximum transfer rate at 24000bps, respectively. |
z, a=26400 |
Set minimum or maximum transfer rate at 26400bps, respectively. |
z, a=28800 |
Set minimum or maximum transfer rate at 28800bps, respectively. |
z, a=33600 |
Set minimum or maximum transfer rate at 33600bps, respectively. |
b=0 |
µ-law encoding |
b=1 |
A-law encoding |
c=0 |
Robbed bit signaling disabled |
c=1 |
Robbed bit signaling enabled |
S(Status) REGISTERS
BREAK OPTIONS |
||
| Type: | Register | |
| Format | AT [cmds] S82=n [cmds] | |
| Description: | Sets the method for break transmission during error-control and ASB connections. | |
Command |
Function |
|
S82=3 |
Expedited signaling, immediately send timed break | |
S82=7 |
Destructive signaling, buffers cleared, immediately send timed break | |
S82=128 |
In-sequence signaling, timed break sent in sequence with transmitted data | |
CONNECTION FAILURE CODES |
|
| Type: | Register |
| Format | AT [cmds] S86? [cmds] |
| Description: | Reports codes which correspond to the possible causes of a connection failure |
Value |
Meaning |
0 |
Normal hang up |
4 |
Carrier signal lost |
5 |
No error-control detected for remote modem during feature negotiation |
9 |
No common protocol found |
12 |
No failure - remote modem disconnected normally |
13 |
Remote modem failed to respond after 10 re-transmissions same message |
14 |
Violation of negotiated protocol caused failure |
ERROR CORRECTION/COMPRESSION |
|
| Type: | Register |
| Format: | AT [cmds] S46=n [cmds] |
| Description: | Selects active error correction and compression protocols |
Command |
Function |
S46=136 |
LAP-M only, no compression |
S46=138 |
LAP-M with V.42bis data compression |
FEATURE NEGOTIATION OPTIONS |
|
| Type: | Register |
| Format: | AT [cmds] S48=n [cmds] |
| Description: | Selects active error correction and compression protocols |
Command |
Function |
S48=0 |
Detection negotiation disabled, XID negotiation disabled |
S48=7 |
Detection negotiation and XID negotiation enabled |
S48=128 |
Fall-back to options set in S36 |