ROCKET DELUXE
| Card Type | Modem |
| Chipset | Unidentified |
| I/O Options | Line in, line out, microphone in, speaker out |
| Maximum Modem Rate | 56.0Kbps |
| Maximum Fax Rate | 14.4Kbps |
| Modem Modulation Protocol | Bell 103/212 ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34, Rockwell VFC, K56flex, V.90 |
| Fax Modulation Protocol | ITU-T V.17, V21 CH2, V27ter, V.29 |
| Fax Class | Class I |
| Error Correction/Compression | MNP5, V.42, V.42bis |
| Data Bus | 32-bit PCI |
CONNECTIONS |
|||
Function |
Label |
Function |
Label |
| Line out (RJ-11) | CN1 |
Speaker out | CN3 |
| Line in (RJ-11) | CN2 |
Microphone in | CN4 |
SUPPORTED COMMAND SET |
Basic AT Commands |
| AT, A/, ‘+++’ |
| A, E, H, M, O, P, Q, T, V, X |
| &C, &F, &M, &P, &V |
Extended AT Commands |
| \N |
| %C, %L, %Q |
S Registers |
| S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S29, S95 |
| Note: See MHI Help File for full command documentation. |
PROPRIETARY AT COMMAND SET
DATA TERMINAL READY (DTR) |
||
| Type: | Configuration | |
| Format: | AT [cmds] &Dn [cmds] | |
| Description: | Selects modem response to DTR | |
Command |
Function |
|
&D0 |
DTR ignored | |
&D1 |
DTR drop causes online command mode | |
| » | &D2 |
DTR drop causes modem to go on-hook |
DIAL |
|
| Type: | Immediate |
| Format: | AT [cmds] D<#> [cmds] |
| Description: | Dials telephone number according to any modifiers included in the string |
| Note: | Any combination of modifiers can be used to produce the desired dial functions in sequence. |
Command |
Function |
DL |
Re-dial last number |
DP |
Pulse dialing enabled |
DT |
Tone dialing enabled/Pulse dialing disabled |
DW |
Dialing resumed following dial tone detection |
D, |
Dialing paused for amount of time specified in S8 register |
D! |
Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. |
D@ |
Wait for quiet Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. |
D; |
Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. |
D^ |
Data calling tone transmission disabled |
FLOW CONTROL |
||
| Type: | Configuration | |
| Format: | AT [cmds] &Kn [cmds] | |
| Description: | Enables flow control options | |
Command |
Function |
|
&K0 |
Flow control disabled | |
&K3 |
RTS/CTS flow control enabled | |
&K4 |
XON/XOFF flow control enabled | |
&K5 |
Transparent XON/XOFF flow control enabled | |
| » | &K6 |
Both RTS/CTS & XON/XOFF flow control enabled |
GUARD TONE |
||
| Type: | Configuration | |
| Format: | AT [cmds] &Gn [cmds] | |
| Description: | Commands the modem to transmit a guard tone in V.22/V.22bis | |
Command |
Function |
|
| » | &G0 |
Guard tone disabled |
&G1 |
Guard tone disabled | |
&G2 |
1800Hz guard tone enabled | |
REPORT INFORMATION |
|
| Type: | Immediate |
| Format: | AT [cmds] In [cmds] |
| Description: | Displays information requested |
Command |
Function |
I3 |
Reports firmware revision |
I4 |
Reports OEM identifier string in either binary or ASCII format |
I6 |
Reports data pump model and internal code |
SOFT RESET |
|
| Type: | Immediate |
| Format: | AT [cmds] Zn [cmds] |
| Description: | Restores modem profiles previously saved in non-volatile RAM using the &W command. |
SPEAKER VOLUME |
|
| Type: | Configuration |
| Format: | AT [cmds] Ln [cmds] |
| Description: | Command non-functional; for compatibility purposes only |
STORE ACTIVE PROFILE |
|
| Type: | Configuration |
| Format: | AT [cmds] &Wn [cmds] |
| Description: | Writes the values for the active profile into the non-volatile RAM |
EXTENDED AT COMMANDS
AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD |
|
| Type: | Configuration |
| Format: | AT [cmds] %En [cmds] |
| Description: | Controls auto-retrain mode and fallback/fall-forward |
Command |
Function |
%E0 |
Auto-retrain disabled |
%E1 |
Auto-retrain enabled |
SPECIAL COMMANDS
BREAK HANDLING IN ERROR CORRECTION MODE |
|
| Type: | Configuration |
| Format: | AT [cmds] +EB=x,y,z [cmds] |
| Description: | Sets break handling options in error correction mode |
Command |
Function |
x=0 |
Break ignored; signal not sent to remote DTE |
y=0 |
Transmitted V.42 signal will not indicate break length signal |
z=30 |
Break is not sent to theDTE |
DATA COMPRESSION REPORTING |
||
| Type: | Configuration | |
| Format: | AT [cmds] +DR=n [cmds] | |
| Description: | Enables/disables data compression reporting | |
| Note: | Reports either ‘NONE’ to indicate date compression disabled, ‘V42B’ to indicate V.42bis data compression, or ‘ALT’ to indicate MNP5 data compression. | |
Command |
Function |
|
| » | +DR=0 |
Data compression reporting disabled |
+DR=1 |
Data compression reporting enabled | |
DATA COMPRESSION |
||
| Type: | Configuration | |
| Format: | AT [cmds] +DS=x,y,z,a [cmds] | |
| Range (z): | 0 - 2048 | |
| Range (a): | 0 - 32 | |
| Description: | Enables/disables data compression (x), disconnect option (y), selects number of dictionary entries (z), and specifies maximum string length (a). | |
| Note: | Reports either ‘NONE’ to indicate date compression disabled, ‘V42B’ to indicate V.42bis data compression, or ‘ALT’ to indicate MNP5 data compression. | |
Command |
Function |
|
x=0 |
Data compression disabled | |
| » | x=3 |
Bidirectional data compression enabled |
y=0 |
Do not disconnect if V.42 fails to negotiaite | |
ERROR CONTROL REPORTING |
||
| Type: | Configuration | |
| Format: | AT [cmds] +ER=n [cmds] | |
| Description: | Enables/disables error control reporting | |
| Note: | Reports either ‘NONE’ to indicate date compression disabled, ‘V42B’ to indicate V.42bis data compression, or ‘ALT’ to indicate MNP5 data compression. | |
Command |
Function |
|
| » | +ER=0 |
Data compression reporting disabled |
+ER=1 |
Data compression reporting enabled | |
ERROR CONTROL AND SYNCHRONOUS MODE SELECTION |
||
| Type: | Configuration | |
| Format: | AT [cmds] +ES=x,y,z [cmds] | |
| Description: | Selects connection mode and error control options | |
Command |
Function |
|
x=1 |
Normal mode | |
x=2 |
V.42 mode | |
x=3 |
V.42 mode with detection phase | |
x=4 |
MNP mode | |
x=6 |
V.80 synchronous access mode in data state | |
| » | y=0 |
All error correction modes optional for fallback function in originate mode |
y=2 |
V.42 or MNP required for fallback in originate mode | |
y=3 |
V.42 error correction required for fallback in originate mode | |
y=4 |
MNP error correction required for fallback in originate mode | |
z=1 |
Error correction disabled; normal mode enabled in answer mode | |
| » | z=2 |
All error correction modes optional for fallback function in answer mode |
z=4 |
V.42 or MNP required for fallback in answer mode | |
z=5 |
V.42 error correction required for fallback in answer mode | |
z=6 |
MNP error correction required for fallback in answer mode | |
z=8 |
V.80 synchronous access mode in data state | |
FLOW CONTROL OPTIONS |
||
| Type: | Configuration | |
| Format: | AT [cmds] +IFC=x,y [cmds] | |
| Description: | Specifies flow control options | |
Command |
Function |
|
x=0 |
Flow control disabled | |
x=1 |
XON/XOFF on transmitted data, signals trapped by local modem | |
| » | x=2 |
CTS/RTS flow control enabled |
x=3 |
XON/XOFF on transmitted data, signals passed through local modem | |
y=0 |
Flow control disabled | |
y=1 |
XON/XOFF on received data | |
| » | y=2 |
CTS/RTS flow control enabled |
MODULATION PROTOCOL REPORTING |
|
| Type: | Immediate |
| Format: | AT [cmds] +MCR? [cmds] |
| Description: | Displays modulation |
MODULATION RATE REPORTING |
|
| Type: | Immediate |
| Format: | AT [cmds] +MRR? [cmds] |
| Description: | Displays minimum rate and maximum rate settings |
MODULATION REPORTING |
||
| Type: | Configuration | |
| Format: | AT [cmds] +MR=n [cmds] | |
| Description: | Enables/disables modulation reporting. +MR=? queries setting | |
| Note: | +MCR and +MRR will not transmit if function is disabled | |
Command |
Function |
|
| » | +MR=0 |
Modulation reporting disabled |
+MR=1 |
Modulation reporting enabled | |
MODULATION SELECTION |
|
| Type: | Configuration |
| Format: | AT [cmds] +MS=x,y,z,a [cmds] |
| Description: | Sets options for active protocol; the transfer rates specified by z and a must be valid for the protocol selected. +MS? queries settings |
Command |
Function |
x=V21 |
V.21 |
x=V22 |
V.22 |
x=V23C |
V.23 |
x=V32 |
V.32 |
x=V34 |
V.34 |
x=103 |
Bell 103 |
x=212 |
Bell 212 |
x=V22B |
V.22bis |
x=V32B |
V.32bis |
x=K56FLEX |
K56flex |
x=V90 |
V.90 |
y=0 |
Automode disabled |
y=1 |
Auto-detect highest speed enabled |
z, a=300 |
Set minimum or maximum transfer rate at 300bps, respectively. |
z, a=1200 |
Set minimum or maximum transfer rate at 1200bps, respectively. |
z, a=2400 |
Set minimum or maximum transfer rate at 2400bps, respectively. |
z, a=4800 |
Set minimum or maximum transfer rate at 4800bps, respectively. |
z, a=7200 |
Set minimum or maximum transfer rate at 7200bps, respectively. |
z, a=9600 |
Set minimum or maximum transfer rate at 9600bps, respectively. |
z, a=12000 |
Set minimum or maximum transfer rate at 12000bps, respectively. |
z, a=14400 |
Set minimum or maximum transfer rate at 14400bps, respectively. |
z, a=16800 |
Set minimum or maximum transfer rate at 16800bps, respectively. |
z, a=19200 |
Set minimum or maximum transfer rate at 19200bps, respectively. |
z, a=21600 |
Set minimum or maximum transfer rate at 21600bps, respectively. |
z, a=24000 |
Set minimum or maximum transfer rate at 24000bps, respectively. |
z, a=26400 |
Set minimum or maximum transfer rate at 26400bps, respectively. |
z, a=28800 |
Set minimum or maximum transfer rate at 28800bps, respectively. |
z, a=33600 |
Set minimum or maximum transfer rate at 33600bps, respectively. |
z, a=56000 |
Set minimum or maximum transfer rate at 56000bps, respectively. |
VOICE COMMANDS
CALLER ID |
|
| Type: | Configuration |
| Format: | AT [cmds] +VCID=n [cmds] |
| Description: | Controls the Caller ID function. +VCID? Queries setting |
Command |
Function |
+VCID=0 |
Caller ID disabled |
+VCID=1 |
Caller ID enabled |
DSVD MODE |
||
| Type: | Configuration | |
| Format: | AT [cmds] -SSE=n [cmds] | |
| Description: | Select whether the modem will use DSVD mode. | |
Command |
Function |
|
| » | -SSE=0 |
DSVD mode disabled. |
-SSE=1 |
DSVD mode enabled. | |