CARDINAL TECHNOLOGIES, INC.
144V32Bis/MVP144IF (ROCKWELL) (VER.2)
| Card Type | Modem |
| Chip Set | Unidentified |
| Maximum Modem Rate | 14.4Kbps |
| Data Modulation Protocol | Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis |
| Error Correction/Compression | MNP5, V.42, V.42bis |
| Data Bus | 8-bit ISA |
| Card Size | Three-quarter length, full-height |
CONNECTIONS |
|||
Function |
Label |
Function |
Label |
| Line in/out | CN1 |
Line in/out | CN2 |
SERIAL PORT ADDRESS |
||||
Setting |
SW1/1 |
SW1/2 |
SW1/3 |
SW1/4 |
COM1 (3F8h) |
On |
On |
On |
Off |
COM2 (2F8h) |
Off |
On |
Off |
On |
COM3 (3E8h) |
On |
Off |
On |
Off |
COM4 (2E8h) |
Off |
Off |
Off |
On |
SUPPORTED COMMAND SET |
Basic AT Commands |
| AT, ‘+++’, A/ |
| A, B, E, H, M, O, V, W, X, Y, Z |
| &C, &F, &G, &L, &T, &V, &W, &Y |
Extended AT Commands |
| \A, \G, \K, \L, \O, \U, \Y, \Z |
| %L, %Q |
S Registers |
| S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S25, S26 |
| S27, S30, S36, S40, S41, S38, S91, S95 |
| Note: See MHI Help File for full command documentation. |
Proprietary AT Command Set
AUTO DATA/SPEED ADJUST |
|
| Type: | Configuration |
| Format: | AT [cmds] Nn [cmds] |
| Description: | Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed. |
Command |
Function |
N0 |
Sets connect speed to match value of S37 |
N1 |
Enables auto data standard and speed is set to match remote modem |
COMMUNICATIONS MODE |
|
| Type: | Configuration |
| Format: | AT [cmds] &Mn [cmds] |
| Description: | Selects communications mode |
Command |
Mode |
&M0 |
Asynchronous mode |
&M1 |
Transmit compression mode |
&M2 |
Receive compression mode |
&M3 |
Enable two-way compression |
COMMUNICATIONS MODE |
|
| Type: | Configuration |
| Format: | AT [cmds] &Qn [cmds] |
| Description: | Selects communications mode options |
Command |
Mode |
&Q0 |
Asynchronous mode, serial port speed follows connect speed. |
&Q4 |
OK result code issued by modem |
&Q5 |
Error correction mode |
&Q6 |
Buffered asynchronous mode |
&Q8 |
MNP mode |
&Q9 |
V.42/V.42bis mode |
DATA SET READY (DSR) |
|
| Type: | Configuration |
| Format: | AT [cmds] &Sn [cmds] |
| Description: | Selects DSR options |
Command |
Function |
&S0 |
DSR forced high |
&S1 |
DSR high only while modem is handshaking or connected |
DATA TERMINAL READY (DTR) |
|
| Type: | Configuration |
| Format: | AT [cmds] &Dn [cmds] |
| Description: | Selects modem response to DTR |
Command |
Function |
&D0 |
Modem does not respond to DTR |
&D1 |
Modem goes to command mode on DTR toggle |
&D2 |
Modem goes to command mode and
disconnects (hangs up) on DTR toggle; Auto-Answer is disabled on low DTR. |
&D3 |
Modem is initialized on DTR toggle |
DIAL |
|
| Type: | Immediate |
| Format: | AT [cmds] D<#> [cmds] |
| Description: | Dials telephone number according to any modifiers included in the string |
| Note: | Any combination of modifiers can be used to produce the desired dial functions in sequence. |
Command |
Function |
DL |
Re-dial last number |
DP |
Pulse dialing enabled |
DR |
Answer mode enabled; originate mode disabled following handshake initiation. |
DS=n |
Dial stored telephone number n |
DT |
Tone dialing enabled/Pulse dialing disabled |
DW |
Dialing resumed following dial tone detection |
D, |
Dialing paused for amount of time specified in S8 register |
D! |
Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. |
D@ |
Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. |
D; |
Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. |
FLOW CONTROL |
|
| Type: | Configuration |
| Format: | AT [cmds] &Kn [cmds] |
| Description: | Enables flow control options |
Command |
Function |
&K0 |
Flow control disabled |
&K3 |
RTS/CTS flow control enabled |
&K4 |
XON/XOFF flow control enabled |
&K5 |
Transparent XON/XOFF flow control enabled |
PULSE DIALING RATIO |
|
| Type: | Configuration |
| Format: | AT [cmds] &Pn [cmds] |
| Description: | Selects pulse dial make/break ratio |
Command |
Function |
&P0 |
39/61ms at 10pps (North America) |
&P1 |
33/67ms at 10pps (Europe) |
&P2 |
39/61ms at 20pps |
REPORT INFORMATION |
|
| Type: | Immediate |
| Format: | AT [cmds] In [cmds] |
| Description: | Displays information requested |
Command |
Function |
I0 |
Reports modem code |
I1 |
Reports ROM checksum |
I2 |
Tests and reports ROM checksum |
I3 |
Reports version information |
RESULT CODES |
|
| Type: | Configuration |
| Format: | AT [cmds] Qn [cmds] |
| Description: | Enables modem to send result codes to the DTE |
Command |
Function |
Q0 |
Result code sending enabled |
Q1 |
Result code sending disabled |
Q2 |
Result code sending enabled only while originating call |
SPEAKER VOLUME |
|
| Type: | Configuration |
| Format: | AT [cmds] Ln [cmds] |
| Description: | Controls speaker volume |
Command |
Function |
L0 |
Low volume setting |
L1 |
Low volume setting |
L2 |
Medium volume setting |
L3 |
Highest volume setting |
STORE TELEPHONE NUMBER |
|
| Type: | Configuration |
| Format: | AT [cmds] &Zn=(phone # & modifiers) |
| Description: | Writes selected telephone numbers into the non-volatile memory at location n |
| Note: The characters described in the D command are valid for use in the &Z command; telephone numbers and modifiers can include up to 30 characters. | |
Extended AT Command
AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD |
|
| Type: | Configuration |
| Format: | AT [cmds] %En [cmds] |
| Description: | Controls auto-retrain mode and fallback/fall-forward |
Command |
Function |
%E0 |
Auto-retrain disabled |
%E1 |
Auto-retrain enabled |
BREAK SEND |
|
| Type: | Configuration |
| Format: | AT [cmds] \Bn [cmds] |
| Range: | 3-9 |
| Unit: | .1 second |
| Description: | Sends break to modem |
BTLZ - CLEAR DICTIONARY |
|
| Type: | Configuration |
| Format: | AT [cmds] %P |
| Description: | Clears BTLZ compression algorithm dictionary |
BTLZ COMPRESSION MODE |
|
| Type: | Configuration |
| Format: | AT [cmds] %Mn [cmds] |
| Description: | Controls compression mode for BTLZ compression algorithm |
Command |
Function |
%M0 |
Disable compression |
%M1 |
Enable transmit compression only |
%M2 |
Enable receive compression only |
%M3 |
Enable two-way compression |
BTLZ DICTIONARY SIZE |
|
| Type: | Configuration |
| Format: | AT [cmds] %Dn [cmds] |
| Description: | Sets dictionary size for BTLZ compression algorithm |
Command |
Function |
%D0 |
512 bytes |
%D1 |
1024 bytes |
%D2 |
2048 bytes |
%D3 |
4096 bytes (one-way) |
BTLZ MAX STRING LENGTH |
|
| Type: | Configuration |
| Format: | AT [cmds] %Sn [cmds] |
| Range: | 6-250 |
| Unit: | ASCII |
| Description: | Controls length of BTLZ compression algorithm string |
COMPRESSION |
|
| Type: | Configuration |
| Format: | AT [cmds] %Cn [cmds] |
| Description: | Selects data compression |
Command |
Function |
%C0 |
Data compression disabled |
%C1 |
Data compression enabled |
CONNECT MODE |
|
| Type: | Configuration |
| Format: | AT [cmds] \Nn [cmds] |
| Description: | Controls the type of connection the modem will operate in |
Command |
Function |
\N0 |
Normal mode enabled |
\N1 |
Direct mode enabled |
\N2 |
Reliable mode enabled |
\N3 |
Auto-reliable mode enabled |
INACTIVITY TIMER |
|
| Type: | Configuration |
| Format: | AT [cmds] \Tn [cmds] |
| Range: | 0-42 |
| Unit: | 1 second |
| Description: | Sets the length of time that the modem does not receive information before it disconnects. |
S(status) Registers
BREAK OPTIONS |
|
| Type: | Register |
| Format | AT [cmds] S82=n [cmds] |
| Description: | Sets the method for break transmission during error-control and ASB connections. |
Command |
Function |
S82=3 |
Expedited signaling, immediately send timed break |
S82=7 |
Destructive signaling, buffers cleared, immediately send timed break |
S82=128 |
In-sequence signaling, timed break sent in sequence with transmitted data |
CONNECTION FAILURE CODES |
|
| Type: | Register |
| Format | AT [cmds] S86? [cmds] |
| Description: | Reports codes which correspond to the possible causes of a connection failure |
Value |
Meaning |
0 |
Normal hang up |
4 |
Carrier signal lost |
5 |
No error-control detected for remote modem during feature negotiation |
9 |
No common protocol found |
12 |
No failure - remote modem disconnected normally |
13 |
Remote modem failed to respond after 10 re-transmissions same message |
14 |
Violation of negotiated protocol caused failure |
DCE LINE SPEED |
|
| Type: | Register |
| Format | AT [cmds] S37=n [cmds] |
| Description: | Sets the maximum allowable data exchange rate attempted during handshake process. |
Command |
Function |
S37=0 |
Speed of last connection |
S37=1 |
75bps |
S37=2 |
110bps |
S37=3 |
300bps |
S37=4 |
600bps |
S37=5 |
1200bps |
S37=6 |
2400bps |
S37=7 |
4800bps |
S37=8 |
7200bps |
S37=9 |
9600bps |
S37=10 |
12.0Kbps |
S37=11 |
14.4Kbps |
ERROR CORRECTION/COMPRESSION |
|
| Type: | Register |
| Format: | AT [cmds] S46=n [cmds] |
| Description: | Selects active error correction and compression protocols |
Command |
Function |
S46=136 |
LAP-M only, no compression |
S46=138 |
LAP-M with V.42bis data compression |
FEATURE NEGOTIATION OPTIONS |
|
| Type: | Register |
| Format: | AT [cmds] S48=n [cmds] |
| Description: | Selects active error correction and compression protocols |
Command |
Function |
S48=0 |
Detection negotiation disabled, XID negotiation disabled, enable LAPM |
S48=7 |
Detection negotiation and XID negotiation enabled |
S48=128 |
Fall-back to options set in S36 |