MOTOROLA, INC.
BITSURFR PRO
| Card Type | ISDN TA |
| Chip Set | Unidentified |
| I/O Options | Analog adapters (2) |
| Transfer Rate | 56Kbps x 2/64Kbps x 2 |
| Data Bus | Serial |
| ISDN Protocol | AIMux, PPP, V.120 |
| Switch Type | 5ESS, DMS-100, NI-1 |
CONNECTIONS |
|||
Function |
Label |
Function |
Label |
| DC power in | CN1 |
Analog adapter 2 | CN4 |
| Serial port | CN2 |
Analog adapter 1 | CN5 |
| ISDN U interface | CN3 |
||
USER CONFIGURABLE SETTINGS |
|||
Setting |
Label |
Position |
|
| » | Factory configured - do not alter | SW1/1 |
Off |
| » | Factory configured - do not alter | SW1/2 |
Off |
| » | Factory configured - do not alter | SW1/3 |
Off |
| » | Factory configured - do not alter | SW1/4 |
Off |
DIAGNOSTIC LED(S) |
|||
LED |
Color |
Status |
Condition |
LS |
Red |
On |
Power is on |
LS |
Green |
On |
TA is ready for operation |
LS |
Red/Green |
Blinking |
ISDN not synchronized |
LS |
N/A |
Off |
Power is off |
1 |
Green |
On |
Call is connected on analog adapter 1 |
1 |
Green |
Blinking |
Call is being connected on analog adapter 1 |
1 |
Green |
Off |
Analog adapter 1 is idle |
2 |
Green |
On |
Call is connected on analog adapter 2 |
2 |
Green |
Blinking |
Call is being connected on analog adapter 2 |
2 |
Green |
Off |
Analog adapter 2 is idle |
DTE |
Green |
On |
Data call connected with V.120 |
DTE |
Green |
Slow blink |
Data call being connected |
DTE |
Green |
Blinking |
Data call connected with single-channel protocol |
DTE |
Green |
Fast blink |
Data call connected with multi-channel protocol |
DTE |
Green |
Off |
Data call not connected |
RD |
Unidentified |
On |
TA is receiving data |
RD |
Unidentified |
Off |
TA is not receiving data |
TD |
Unidentified |
On |
TA is transmitting data |
TD |
Unidentified |
Off |
TA is not transmitting data |
SUPPORTED STANDARD COMMANDS |
Basic AT Commands |
| +++, A/ |
| A, E, H, O, V, W, X, Z |
| &F, &M, &R, &S, &W, &Y, &Z |
Extended AT Commands |
| \Q |
S-Registers |
| S0, S1, S2, S3, S4, S5, S7, S10, S12, S18, S25, S26 |
| Note:See MHI help file for complete information. |
Proprietary AT Command Set
AUTHENTICATION PROTOCOL |
||
| Type: | Configuration | |
| Format: | AT [cmds] @M2= x [cmds] | |
| Description: | Selects the authentication protocol the TA will use. | |
Command |
Function |
|
@M2=C |
TA will use CHAP-MD5 authentication protocol. | |
@M2=M |
TA will use CHAP-MS authentication protocol. | |
| » | @M2=N |
TA will not use authentication protocol. |
@M2=P |
TA will use PAP authentication protocol. | |
COMMAND SET |
||
| Type: | Configuration | |
| Format: | AT [cmds] @P1= n [cmds] | |
| Description: | Selects the command set the TA will use. | |
Command |
Function |
|
| » | @P1=A |
AT command set enabled. |
@P1=N |
Command sets disabled | |
@P1=VB |
V.25bis command set in bisynchronous mode enabled. | |
@P1=VH |
V.25bis command set in HDLC mode enabled. | |
FIRMWARE UPGRADE PASSWORD |
|
| Type: | Configuration |
| Format: | AT [cmds] %P1= xxxxxxxx [cmds] |
| Description: | Sets the password required to upgrade the firmware to the string indicated. The password must be eight characters or less, case sensitive. If the password is set to a capital D, the password check will be disabled. |
LOCAL SERIAL PORT SPEED |
||
| Type: | Configuration | |
| Format: | AT [cmds] @P2= n [cmds] | |
| Description: | Sets the speed of the local serial port. | |
Command |
Function |
|
@P2=300 |
Sets serial port speed to 300bps. | |
@P2=1200 |
Sets serial port speed to 1200bps. | |
@P2=2400 |
Sets serial port speed to 2400bps. | |
@P2=4800 |
Sets serial port speed to 4800bps. | |
@P2=9600 |
Sets serial port speed to 9600bps. | |
@P2=19200 |
Sets serial port speed to 19.2Kbps. | |
@P2=38400 |
Sets serial port speed to 38.4Kbps. | |
@P2=48000 |
Sets serial port speed to 48Kbps. | |
@P2=56000 |
Sets serial port speed to 56Kbps. | |
@P2=57600 |
Sets serial port speed to 57.6Kbps. | |
@P2=64000 |
Sets serial port speed to 64Kbps. This disables serial port speed auto-detection. | |
@P2=112000 |
Sets serial port speed to 112Kbps. | |
| » | @P2=115200 |
Sets serial port speed to 115.2Kbps. |
@P2=128000 |
Sets serial port speed to 128Kbps. This disables serial port speed auto-detection. | |
MENU SYSTEM |
|
| Type: | Immediate |
| Format: | AT [cmds] @MENU |
| Description: | Enters the LocalMenu menu configuration system. |
See document MOTOROLA, INC. BITSURFR PRO EZ for a full command summary.