SATISFAXTION 428

WILDCARD TECHNOLOGIES, INC.

SATISFAXTION 428

Card Type	Modem (synchronous/asynchronous)
Processor	Motorola MC68356 (processor), 56002 (DSP)
Processor Speed	25MHz (processor), 60MHz (DSP)
Chipset	Unidentified
Maximum Onboard Memory	512KB RAM
Maximum Data Rate	28.8Kbps
Maximum Fax Rate	14.4Kbps
Data Bus	8/16-bit ISA
Fax Class	Unidentified
Data Modulation	Bell 103A/212A ITU-T V.21, V.22, V.23, V.22bis, V.32, V.32bis, V.34
Fax Modulation	ITU-T V.17, V.21CH2, V.27ter, V.29, V.33
Error Correction/Compression	MNP5, V.42, V.42bis

DIAGNOSTIC LED(S) (POWER-UP)
LED2	LED3	LED4	Condition
Off	On	On	ROM code initialized and hardware devices mapped
On	Off	On	Serial devices set up and ROM checksum passed
On	On	Off	Memory test passed
On	On	On	Modem set up and CPU test passed
Off	Off	On	All tests passed
Note:On power-up, the board should proceed in order through the conditions listed above. Any other LED patterns or failure to proceed to the next condition indicate a hardware failure.

DIAGNOSTIC LED(S) (SOFTWARE DRIVER INITIALIZATION)
LED1	LED2	LED3	LED4	Condition
Off	Off	On	Off	Base I/O address for fax set
Off	On	Off	Off	Base I/O address for serial port set
On	On	Off	Off	Interrupt for fax set
On	Off	On	Off	Interrupt for serial port set
On	Off	Off	On	Interrupt test passed
On	Off	On	On	Software configuration written to board
On	On	Off	On	Software configuration read from board
On	On	On	Off	Hardware configuration read from board
On	Off	Off	Off	FIFO interface set to 16-bit mode
On	On	On	On	Application data loaded
Off	Off	Off	Off	Application executing
Note:When the software driver is loaded, the board should proceed in order through the conditions listed above. Any other LED patterns or failure to proceed to the next condition indicate a software failure. The color of LED1 is unidentified.

SUPPORTED STANDARD COMMANDS

Basic AT Commands

+++, ‘comma’, A/

A, C, D, E, F, H, L, M, N, O, P, Q, T, V, W, X, Y, Z

&C, &D, &F, &G, &K, &L, &M, &P, &Q, &R, &S, &T, &U, &V, &W, &X, &Y, &Z

Extended AT Commands

\A, \B, \C, \G, \J, \K, \L, \N, \Q, \T, \U, \V, \X, \Y, \Z

%A, %C, %E

Special AT Commands

-C, -J, "H, "O

S-Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S12, S14, S16, S18, S21, S22, S23, S25, S26, S27,

S30, S37, S95, S108, S109, S110

Note:See MHI documentation for complete information.

Proprietary AT Command Set

DETECT 400HZ TONE
Type:		Configuration
Format:		AT [cmds] %H n [cmds]
Description:		Selects whether the modem will detect the 400Hz tone.
Command		Function
	%H0	400Hz detection enabled.
»	%H1	400Hz detection disabled.

DISPLAY FIRMWARE VERSION
Type:	Immediate
Format:	AT [cmds] -V n [cmds]
Description:	Displays the version of the modem’s firmware.

LOCAL SERIAL PORT SPEED
Type:		Register
Format:		AT [cmds] S112= n [cmds]
Description:		Selects the speed ot the serial port.
Command		Function
»	S112=0	Auto-detect speed of last entered command.
	S112=2	Select 300bps.
	S112=3	Select 1200bps.
	S112=4	Select 2400bps.
	S112=5	Select 4800bps.
	S112=6	Select 7200bps.
	S112=7	Select 9600bps.
	S112=8	Select 12Kbps.
	S112=9	Select 14.4Kbps.
	S112=10	Select 16.8Kbps.
	S112=11	Select 19.2Kbps.
	S112=12	Select 38.4Kbps.
	S112=13	Select 57.6Kbps.
	S112=14	Select 600bps.

PROTOCOL/SPEED
Type:		Configuration
Format:		AT [cmds] B n [cmds]
Description:		Selects the protocol and line speed the modem will attempt to connect at.
Command		Function
	B0	Selects V.21 at 300bps or V.22 at 1200bps.
	B1	Selects Bell 103 at 300bps or Bell 212A at 1200bps.
	B2	Selects V.23 at 75/1200 in originate mode and V.23 at 1200/75 in answer mode.
	B3	Selects V.23 at 1200/75 in originate mode and V.23 at 75/1200 in answer mode.
	B15	Selects V.21 at 300bps.
	B16	Selects Bell 103 at 300bps.
	B30	Selects V.22bis at 2400bps.
	B41	Selects V.32 at 4800bps.
	B42	Selects V.34 at 4800bps.
	B52	Selects V.32bis at 7200bps.
	B53	Selects V.34 at 7200bps.
	B60	Selects V.32 at 9600bps.
	B61	Selects V.34 at 9600bps.
	B70	Selects V.32bis at 12Kbps.
	B71	Selects V.34 at 12Kbps.
	B75	Selects V.32bis at 14.4Kbps.
	B76	Selects V.34 at 14.4Kbps.
	B80	Selects V.34 at 16.8Kbps.
	B85	Selects V.34 at 19.2Kbps.
	B90	Selects V.34 at 21.6Kbps.
	B95	Selects V.34 at 24Kbps.
	B100	Selects V.34 at 26.8Kbps.
»	B105	Selects V.34 at 28.8Kbps.

REPORT INFORMATION
Type:	Immediate
Format:	AT [cmds] I n [cmds]
Description:	Displays information requested.
Command	Function
I0	Reports modem model and speed.
I1	Reports ROM checksum.
I2	Tests and reports ROM checksum.
I3	Reports ROM part number and version.
I4	Reports modem capabilities.

V.32 - AUTO-RETRAIN
Type:		Configuration
Format:		AT [cmds] &B n [cmds]
Description:		Controls auto-retrain function if poor line quality is detected.
Command		Function
	&B0	Auto-retrain disabled, modem hangs up.
»	&B1	Auto-retrain enabled, modem hangs up if retrain fails.
	&B2	Auto-retrain disabled, modem does not hang up.