TANDBERG DATA
DLT4000 (EXTERNAL)
| Device Type | External tape drive |
| Interface | SCSI-2 Fast Wide |
| Format | DLT |
| Sustained Transfer Rate | 3.0 MBPS (Compressed) |
| View | Top |
DRIVE SELECT ID |
| Note: Drive ID's are selected via SW1. Use buttons 1 or 2 to select a higher or lower SCSI ID. The current ID selection will appear in the viewing window. |
MANUFACTURERS RECOMMENDED MEDIA |
||
| Tape | Capacity without Compression | Capacity With Compresion |
| DLT Tape III | 10.0 GB |
20.0 GB |
| DLT Tape IIIxt | 15.0 GB |
30.0 GB |
| DLT Tape IV | 20.0 GB |
40.0 GB |
DIAGNOSTIC LED(S) |
|||
LED |
Color |
Status |
Condition |
LED1 |
Yellow |
On |
Compression mode enabled (10.0, 15.0, and 35.0GB densities only). |
LED1 |
Yellow |
Off |
Compression mode disabled. |
LED2 |
Yellow |
On |
Density from front panel selected. Density to be selected by the host (automatic). |
LED2 |
Yellow |
Off |
Density selected from front panel |
LED2 |
Yellow |
Blinking |
Density to be selected by the host (automatic) |
LED2 |
Yellow |
Blinking |
Post error |
LED4 |
Orange |
On |
Cartridge is write-protected. |
LED4 |
Orange |
Off |
Cartridge is write-enabled. |
LED5 |
Yellow |
Blinking |
Cartridge is loaded and tape is moving. |
LED5 |
Yellow |
On |
Cartridge is loaded and ready for use. |
LED6 |
Yellow |
On |
Drive head requires cleaning, or tape is bad. |
LED6 |
Yellow |
Remains on after cleaning tape unloaded |
Cleaning tape attempted to clean drive head, tape expired, cleaning not performed. |
LED6 |
Yellow |
Turns on when data cartridge loaded after cleaning |
Problem data cartridge. Insert a different cartridge. |
LED6 |
Yellow |
Off |
Cleaning complete, or cleaning unnecessary. |
LED7 |
Green |
On |
Okay to operate cartridge insert/release handle |
LED7 |
Green |
Off |
Do not operate cartridge insert/release handle |
LED7 |
Green |
Blinking |
Close handle and wait for steady green indication before inserting cartridge. |
2.6 |
Yellow |
On |
Indicates tape is recorded in 2.6GB format. |
2.6 |
Yellow |
Blinking |
Indicates tape is recorded in another density selected for a write from BOT. |
6.0 |
Yellow |
On |
Indicates tape is recorded in 6.0GB format. |
6.0 |
Yellow |
Blinking |
Indicates tape is recorded in another density selected for a write from BOT. |
10.0/15.0 |
Yellow |
On |
Indicates tape is recorded in 10.0GB format if DLT tape III is used. Indicates tape is recorded in 15.0GB format if DLT tape IIIxt is used. |
10.0/15.0 |
Yellow |
Blinking |
Indicates tape is recorded in another density selected for a write from BOT. |
20.0 |
Yellow |
On |
Indicates tape is recorded in 20.0GB format. |
20.0 |
Yellow |
Blinking |
Indicates tape is recorded in another density selected for a write from BOT. |
| Note: All four right side or all seven left side indicators ‘On’ designates that the Power-on self-test (POST) is starting. All four right side or all seven left side indicators ‘Blinking’ designates that an error has occurred in the POST; clear the error by pressing the unload button, or turn drive power off and then on again. If error remains service is required. | |||