TANDBERG DATA
DLT 4000 (INTERNAL)
Device Type | Internal Tape Drive |
Interface | SCSI-2 Fast Wide |
Format | DLT |
Sustained Transfer Rate | 1.5 MBPS/3.0 MBPS (compressed) |
Size | 5.25 in. full height |
View | Top |
CONNECTIONS |
|
Function |
Label |
Proprietary Power connector | CN1 |
USER CONFIGURABLE SETTINGS |
|||
Setting |
Label |
Position |
|
» | Factory configured - do not alter. | JP1/Pins 1 & 2 |
Unidentified |
» | TERMPWR supplied by drive | JP1/Pins 3 & 4 |
Closed |
TERMPWR supplied by SCSI interface to drive | JP1/Pins 3 & 4 |
Open |
|
» | Factory configured - do not alter. | JP1/Pins 5 - 26 |
Unidentified |
» | Factory configured - do not alter. | JP2 |
Unidentified |
» | Factory configured - do not alter. | JP3 |
Unidentified |
» | Remote ID enabled | JP4/Pins 1 & 2 |
Closed |
Remote ID disabled | JP4/Pins 1 & 2 |
Open |
|
Parity check disabled | JP4/Pins 3 & 4 |
Closed |
|
Parity check enabled | JP4/Pins 3 & 4 |
Open |
|
» | Factory configured - do not alter. | JP4/Pins 5 - 10 |
Unidentified |
» | Factory configured - do not alter. | JP5 |
Unidentified |
DRIVE SELECT ID |
|||
Drive ID |
JP4/Pins 5 & 6 |
JP4/Pins 7 & 8 |
JP4/Pins 9 & 10 |
0 |
Open |
Open |
Open |
1 |
Open |
Open |
Closed |
2 |
Open |
Closed |
Open |
3 |
Open |
Closed |
Closed |
4 |
Closed |
Open |
Open |
5 |
Closed |
Open |
Closed |
6 |
Closed |
Closed |
Open |
7 |
Closed |
Closed |
Closed |
Note: Pins 1 & 2 of JP4 are to be closed when selecting SCSI IDs. |
MANUFACTURERS RECOMMENDED MEDIA |
||
Tape |
Capacity Without Compression |
Capacity With Compression |
DLT tape III |
10GB |
20GB |
DLT tape IIIxt |
15GB |
30GB |
DLT tape IV |
20GB |
40GB |
DIAGNOSTIC LED(S) |
|||
LED |
Color |
Status |
Condition |
LED1 |
Yellow |
On |
Compression mode enabled (10.0, 15.0, and 35.0GB densities only). |
LED1 |
Yellow |
Off |
Compression mode disabled. |
LED2 |
Yellow |
On |
Density from front panel selected. Density to be selected by the host (automatic). |
LED2 |
Yellow |
Off |
Density selected from front panel |
LED2 |
Yellow |
Blinking |
Density to be selected by the host (automatic) |
LED2 |
Yellow |
Blinking |
Post error |
LED4 |
Orange |
On |
Cartridge is write-protected. |
LED4 |
Orange |
Off |
Cartridge is write-enabled. |
LED5 |
Yellow |
Blinking |
Cartridge is loaded and tape is moving. |
LED5 |
Yellow |
On |
Cartridge is loaded and ready for use. |
LED6 |
Yellow |
On |
Drive head requires cleaning, or tape is bad. |
LED6 |
Yellow |
Remains on after cleaning tape unloaded |
Cleaning tape attempted to clean drive head, tape expired, cleaning not performed. |
LED6 |
Yellow |
Turns on when data cartridge loaded after cleaning |
Problem data cartridge. Insert a different cartridge. |
LED6 |
Yellow |
Off |
Cleaning complete, or cleaning unnecessary. |
LED7 |
Green |
On |
Okay to operate cartridge insert/release handle |
LED7 |
Green |
Off |
Do not operate cartridge insert/release handle |
LED7 |
Green |
Blinking |
Close handle and wait for steady green indication before inserting cartridge. |
2.6 |
Yellow |
On |
Indicates tape is recorded in 2.6GB format. |
2.6 |
Yellow |
Blinking |
Indicates tape is recorded in another density selected for a write from BOT. |
6.0 |
Yellow |
On |
Indicates tape is recorded in 6.0GB format. |
6.0 |
Yellow |
Blinking |
Indicates tape is recorded in another density selected for a write from BOT. |
10.0/15.0 |
Yellow |
On |
Indicates tape is recorded in 10.0GB format if DLT tape III is used. Indicates tape is recorded in 15.0GB format if DLT tape IIIxt is used. |
10.0/15.0 |
Yellow |
Blinking |
Indicates tape is recorded in another density selected for a write from BOT. |
20.0 |
Yellow |
Blinking |
Indicates tape is recorded in another density selected for a write from BOT. |
20.0 |
Yellow |
On |
Indicates tape is recorded in 20.0GB format. |
Note: All four right side or all seven left side indicators On designates that the Power-on self-test (POST) is starting. All four right side or all seven left side indicators Blinking designates that an error has occurred in the POST; clear the error by pressing the unload button, or turn drive power off and then on again. If error remains service is required. |