ADVANCED DIGITAL INFORMATION CORPORATION
DS9400D, DS9400D/L
|
Device Type |
External Tape Drive |
|
Interface |
SCSI-2 |
|
Format |
DLT |
|
Sustained Transfer Rate |
3.0 MBPS |
|
View |
Top |
|
CONNECTIONS |
|||
|
Function |
Label |
Function |
Label |
|
Power connector |
CN1 |
SCSI-2 connector |
CN3 |
|
SCSI-2 connector |
CN2 |
Power switch |
SW2 |
|
DRIVE SELECT ID |
|
Note : SCSI ID is selected by activating SW1 until the desired number is displayed in the viewing window. |
FRONT PANEL
|
DIAGNOSTIC LED(S) |
|||
|
LED |
Color |
Status |
Condition |
|
LED1 |
Yellow |
On |
Tape density is 2.6GB |
|
LED1 |
Yellow |
Blinking |
Tape density is not 2.6GB |
|
LED2 |
Yellow |
On |
Tape density is 6.0GB |
|
LED2 |
Yellow |
Blinking |
Tape density is not 6.0GB |
|
LED3 |
Yellow |
On |
Tape density is 10.0GB |
|
LED3 |
Yellow |
Blinking |
Tape density is not 10.0GB |
|
LED4 |
Yellow |
On |
Tape density is 20.0GB |
|
LED4 |
Yellow |
Blinking |
Tape density is not 20.0GB |
|
LED5 |
Yellow |
On |
Compression mode is enabled |
|
LED5 |
Yellow |
Off |
Compression mode is not enabled |
|
LED6 |
Yellow |
On |
Tape density has been selected from front panel |
|
LED6 |
Yellow |
Blinking |
Unit is in tape density selection mode |
|
LED6 |
Yellow |
Off |
Tape density has been selected from host |
|
LED7 |
Orange |
On |
Tape in drive is write-protected |
|
LED7 |
Orange |
Off |
Tape in drive is not write-protected |
|
LED8 |
Yellow |
On |
Tape loaded; unit is ready |
|
LED8 |
Yellow |
Blinking |
Tape is being inserted or ejected |
|
LED9 |
Yellow |
On |
Tape drive needs cleaning or tape is bad |
|
LED9 |
Yellow |
Off |
Cleaning is complete or drive does not need cleaning |
|
LED10 |
Green |
On |
Okay to use the cartridge handle |
|
LED10 |
Green |
Off |
Do not use the cartridge handle |
DLT4000 TAPE DRIVE
|
TERMINATION POWER SELECTION |
||
|
Setting |
JP1/1 & 2 |
JP1/3 & 4 |
|
Termination power disabled; active termination disabled |
Open |
Open |
|
Termination power enabled; active termination disabled |
Closed |
Open |
|
Termination power disabled; active termination enabled |
Open |
Closed |
|
Termination power enabled; active termination enabled |
Closed |
Closed |
|
SCSI BUS PARITY |
|
|
Setting |
JP2 |
|
Disable SCSI parity checking |
Pins 3 & 4 closed |
|
Enable SCSI parity checking |
Pins 3 & 4 open |
|
MANUFACTURERS RECOMMENDED MEDIA |
||
|
Tape |
Capacity Without Compression |
Capacity With Compression |
|
DLTTape III |
10GB |
20GB |
|
DLTTape IIIXT |
15GB |
30GB |
|
DLTTape IV |
20GB |
40GB |