TECMAR TECHNOLOGIES, INC.
WANGDAT 3300DX
| Device Type | Internal Tape Drive |
| Interface | SCSI, SCSI-2 |
| Format | DDS, DDS-2 |
| Sustained Transfer Rate | 366KBPS |
| Size | 3.5 in. half height |
| View | Top |
USER CONFIGURABLE SETTINGS |
|||
Setting |
Label |
Position |
|
| » | Factory configured - do not alter | JP1 | Pins 7 & 8 open |
| » | Termination enabled | JP1 | Pins 9 & 10 closed |
| Termination disabled | JP1 | Pins 9 & 10 open | |
| » | TERMPWR supplied by SCSI interface to drive | JP1 | Pins 11 & 12 closed |
| TERMPWR supplied by drive | JP1 | Pins 11 & 12 open | |
| » | Factory configured - do not alter | SW1/1 | Off |
| » | Parity enabled | SW1/2 | On |
| Parity disabled | SW1/2 | Off | |
| » | SCSI-2 protocol selected | SW1/3 | On |
| SCSI-1 protocol selected | SW1/3 | Off | |
| » | Cartridge eject disabled1 | SW1/4 | Off |
| Cartridge eject enabled2 | SW1/4 | On | |
| » | Factory configured - do not alter | SW1/5 | Off |
| » | Factory configured - do not alter | SW1/6 | Off |
| » | Factory configured - do not alter | SW1/7 | Off |
| » | Factory configured - do not alter | SW1/8 | Off |
| Note: 1) With 1/4
switched to the Off position, the unload command will cause the drive to rewind the
cartridge to the beginning of the tap, but will not eject the cartridge. 2) With 1/4 switched to the On position, the unload command will cause the drive to rewind the cartridge to the beginning of the tap, and will then eject the cartridge. |
|||
DRIVE SELECT ID |
||||
Drive ID |
JP1/Pins 1 & 2 |
JP1/Pins 3 & 4 |
JP1/Pins 5 & 6 |
|
| » | 0 |
Open |
Open |
Open |
1 |
Closed |
Open |
Open |
|
2 |
Open |
Closed |
Open |
|
3 |
Closed |
Closed |
Open |
|
4 |
Open |
Open |
Closed |
|
5 |
Closed |
Open |
Closed |
|
6 |
Open |
Closed |
Closed |
|
7 |
Closed |
Closed |
Closed |
|
MANUFACTURERS RECOMMENDED MEDIA |
|
Tape |
Capacity |
| 60 meter DDS cartridge | 1.3 GB |
| 90 meter DDS cartridge | 2.0 GB |
| 120 meter DDS cartridge | 4.0 GB |
DIAGNOSTIC LEDS |
|||
LED |
Color |
Status |
Condition |
| LED1 | Green |
On |
Drive active on SCSI bus |
| LED1 | Amber |
Pulsing1 |
Command in process, disconnected from SCSI bus |
| LED1 | Red |
Blinking |
Drive fault condition exists |
| LED1 | Amber | Blinking2 | Drive heads require cleaning |
| LED2 | Amber | Blinking2 | Drive heads require cleaning |
| LED2 | Amber | On | Cartridge is loading or unloading |
| LED2 | Amber | Blinking | Cartridge in place |
| LED2 | Green | On | Cartridge in place |
| Note:
1) Once every 5 seconds. 2) Blinking Amber in unison with prospective LED. LEDs are multi-colored and serve multiple functions as described. Exact location of LEDs is unidentified. "LED1" refers to the "left" LED of the front panel of the drive as described in the users manual, and indicates Activity/Fault related functions. "LED2" refers to the "right" LED on the front panel of the drive as described in the users manual, and indicates Cartridge/Compression related functions. |
|||